What are your opinions with regards to How to Install a Bathtub Yourself?
Installing a bathtub isn't precisely brain surgery, yet it does call for strong plumbing, carpentry, and in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult project. If the old tub is easily accessible, the project can move rapidly; if you have to open up a wall surface to get rid of the old bathtub and position the new tub, the job is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to move out the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the task as well as are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed task, it is far better to think about utilizing one before you begin. Chances are you may require a specialist plumber to make tube links.
This short article will help you install a brand-new tub in your shower room if you have already bought a brand-new bathtub as well as don't require to transform the plan of your previous supply of water pipelines.
Your devices as well as material checklist need to make up the following:
Planning for the Setup
Firstly, the sustaining framework supplied with the bathroom must be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to prevent pressure on the tub.
Fit the flexible tap adapters to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be rather problematic due to the limited accessibility that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have been gotten rid of, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before proceeding to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by examining the level and also adjusting the feet on the bathtub up until the level checks out degree.
To mount faucets, fit the bottom of the furthest flexible tap port to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply and check all joints and new pipework for leaks and also tighten them if essential. Load the bath tub as well as likewise inspect the overflow outlet and the normal electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the bathtub ought to wait till the bath tub has actually been utilized a minimum of when as this will resolve it right into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making certain that the washers are in area between the tap as well as the sink. Protect the faucet in place with the supplier given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall in between the bath as well as the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the activity experienced when the bathtub is in use. The sealer can crack relatively very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
I was introduced to that write-up about Installing A Bathtub from an acquaintance on another blog. Sharing is caring. Helping people is fun. Thank you for your time. Visit again soon.
Get Estimate